Wall-mounted and floor-standing batteries can use similar electrical building blocks, yet they create different site and service requirements. The choice is not cosmetic. It affects structural support, working clearance, cable entry, lifting, water exposure and replacement access.
A distributor should therefore qualify the installation method along with capacity and inverter compatibility.
Een gerelateerde HMX-referentie is het wall-mounted home batteries. Gebruik dit als kader voor het volgende leveranciersgesprek en leg projectspecifieke afwijkingen vast voordat u bestelt.
Direct antwoord: Select the mounting method after a site survey. Record wall material or floor condition, clearances, route to the inverter, expected water level, ventilation and the method for moving the unit safely.
Onderzoeksbeoordelingsdatum: 30 september 2026. Kwantitatieve uitspraken zijn gekoppeld aan de gelinkte bron en moeten opnieuw worden gecontroleerd als de inkoop later plaatsvindt.
Gebruik voor de definitieve beoordeling van het bewijsmateriaal IEC 63056:2020 toepassingsgebied as a source check. IEC 63056 adds safety requirements for secondary lithium cells and batteries used in electrical energy storage systems up to 1,500 V DC nominal.
Definieer de grens
For Solar distributors, installers and residential project firms, the first task is to turn the intended service into measurable inputs and acceptance limits. The following table keeps the decision tied to evidence instead of a broad product label.
| Factor | Wandmontage | Floor-standing |
|---|---|---|
| Support | Depends on wall structure and approved fixings | Depends on level, load-bearing floor |
| Handling | Lifting and alignment at height | Floor movement and anti-tip measures |
| Cable route | Often short and visible near inverter | May allow lower cable entry |
| Flood exposure | Can place battery above floor level | Requires suitable plinth or location where needed |
| Service access | Front/side clearance plus removal path | Access plus space to move the unit |
Kopers die de initiële scope definiëren, kunnen deze vereisten vergelijken met HMX's floor-standing home batteries. De pagina is een product- of projectreferentie; definitieve geschiktheid vereist nog steeds een schriftelijke projectspecificatie.
Raadpleeg voor de huidige markt- en beleidscontext IEC 62619:2022 toepassingsgebied. IEC 62619:2022 behandelt veiligheidseisen en tests voor secundaire lithiumcellen en -batterijen die worden gebruikt in industriële toepassingen, waaronder stationaire en mobiele toepassingen.
Installation details that decide the format
These are the practical objections and failure modes most likely to stop approval, delay commissioning or create an avoidable service call for Solar distributors, installers and residential project firms.
- Wall construction and anchor loads are assumed rather than verified.
- A floor unit is placed in a flood-prone or obstructed service area.
- Cable bend radius and the removal path are omitted from the layout.
Vragen die de koper vóór goedkeuring moet stellen
- Can technicians isolate and remove the battery safely?
- Does the location meet clearance, heat and water-exposure limits?
- Who verifies anchors, floor loading and protected cable routes?
Acceptatie- en faaltests
De commerciële offerte moet haar aannames, uitsluitingen en meetgrens vermelden. Kopers kunnen systemen dan op dezelfde basis vergelijken en latere ontwerpwijzigingen onder documentbeheer houden.
| Survey item | Record | Do not assume |
|---|---|---|
| Wall or floor | Material, condition and loading | That any masonry is suitable |
| Clearance | Manufacturer minimums and local rules | That a tight closet is acceptable |
| Temperature | Daily maximum at battery position | That room average equals battery temperature |
| Moisture | Leaks, condensation and flood risk | That indoor means dry |
| Access | Door width, stairs and lifting route | That installers can move the unit safely |
Actiepunten voor het projectteam
- Use only the mounting hardware and orientation approved for the model.
- Keep DC protection and cable sizing within the system design.
- Plan replacement access before cabinets and furniture are fixed.
- Photograph the completed installation and label isolation points.
De technische vergelijking moet ook worden getoetst aan NREL PVWatts Calculator. PVWatts estimates grid-connected PV energy production from location and system inputs. It is useful for the PV side of a study, but it does not replace interval-load and outage analysis for battery sizing.
Make installation and service access part of product selection
A wall-mounted unit transfers static and service loads into the wall and anchors. The installer should identify the wall construction, approved fasteners, mounting surface and cable forces rather than relying on appearance. A floor-standing unit needs a level, load-capable base and protection from standing water, vehicle impact and blocked ventilation.
Pas voor een concrete beoordeling op apparatuurniveau de bovenstaande controles toe op het 10kWh wall-mounted LiFePO4 battery en vraag bevestiging voor de beoogde locatieomstandigheden en bedrijfsmodus.
Draw the working clearance, isolation point, cable bend radius and removal path. Service may require opening covers, reaching connectors or moving the complete battery, so the installed position must support those tasks without dismantling unrelated equipment. Keep escape routes, electrical panels and household storage areas clear.
Voor specificatie- en acceptatiewerk, UNECE Manual of Tests and Criteria, Revision 8 provides an independent reference. UNECE publishes the current Manual of Tests and Criteria and its 2025 amendment, including changes affecting subsection 38.3 for lithium cells and batteries.
Environmental suitability remains separate from mounting style. Confirm temperature range, direct sun, humidity, dust, corrosive exposure and water risk against the named product documentation. Photograph anchors, cable protection, labels and final clearances, then include them with commissioning measurements in the installation record.
Van analyse naar een controleerbare beslissing
- Survey structure, floor level, water exposure and working clearances.
- Approve the mounting and cable route before delivery.
- Verify isolation, ventilation and a safe battery removal path.
- Record anchors, labels, settings and commissioning results at handover.
Document the installed configuration
Compatibility and safety depend on the equipment as installed, not only on a catalogue selection. Preserve model and firmware identifiers, wiring and protection drawings, physical clearances, settings and test conditions. Later service work should begin from this baseline and record every approved change.
Dezelfde bewijs- en acceptatievragen kunnen worden gebruikt bij het beoordelen van HMX's 16kWh floor-standing LiFePO4 battery; catalogusinformatie moet worden afgestemd op de gecontroleerde offerte en tekeningen.
- Named equipment, firmware, accessories, cables and communication settings.
- As-built electrical and physical drawings with isolation points identified.
- Commissioning results for normal operation, limits and selected failure states.
- Backups, photographs, change log and a technician recovery procedure.
After service or firmware work, compare the returned system with the approved baseline and repeat affected tests. This makes later troubleshooting faster and prevents an undocumented field change from invalidating a compatibility or safety conclusion.
Decision Rule
Choose the option that satisfies the site conditions, service objective and maintenance model with the clearest test evidence. A larger nameplate or broader marketing claim is not a substitute for fit.